The power supply cable RVA-0106M-1.25FF-1 and ST-LINK/V2 SWD programing cable RVA-SWD-06M-C100 are included as free accessories for single package.

Main features:

  • 10.1’’ TFT display
  • 1280x800px resolution
  • High brightness 850cd/m2
  • Full viewing angles (IPS)
  • STM32H757XIH6 (2MB Flash, 1MB RAM) microcontroller
  • All STM32H7 interfaces
  • Optical bonding
  • Industrial projected capacitive touch screen
  • Black decorative cover glass
  • High quality – zero bad pixels
  • 64MB QSPI
  • 8MB SDRAM
  • TouchGFX direct support
  • Power Supply: 6V-48V

Description

High performance
STM32 MCU

STM32 Embedded Display series from Riverdi are currently, the highest resolution (1280×800 pixel) displays with STM32H757XIH6 on the market.

Dual core: it combines high-performance Arm® Cortex®-M7 and Cortex®-M4 32-bit RISC cores. The Cortex®-M7 core operates at up to 480 MHz and the Cortex®-M4 core at up to 240 MHz. Both cores feature a floating-point unit (FPU) which supports Arm® single- and double-precision (Cortex®-M7 core) operations and conversions (IEEE 754 compliant), including a full set of DSP instructions and a memory protection unit (MPU) to enhance application security.

It features a 2 Mb flash memory that can be used for storing programs and data.

High RAM size: 1 Mb

 

 

 

Multi-Interfaces

RS485

RS232

Expansion connector

The board offers additional and independent GPIOs over a 40pin, 1.27mm male header. It provides direct access to the below GPIOs of MCU STM32, that makes it possible to be easily extended by an addon board for specific application.

List of interfaces on Expansion connector:

  • 2 x I2C
  • 1 x UART
  • 1 x USART
  • 1 x SPI
  • 1 x USB
  • 7 x PWMs
  • 2 x DACs (Digital-to-analog)
  • 2 x ADCs (Analog-to-digital)

 

Fully independent 2xCAN FD

Applicable in industrial and automotive area.

Fast-programming SWD port

SWD connector allows to program STM32 and QSPI with customer’s applications. Riverdi developed the ST-LINK programming cable that is included in the STM32 Embedded Display sample package (single packing).

RiBUS

In some applications there might be a need to connect a second display in one device. With the STM32 Embedded Display line it is very easy as these displays are equipped with Master RiBUS connector – universal interface to Riverdi’s intelligent displays. In this way, the second display does nots need an external host controller and 2 independent displays can be controlled by one STM32.

USB

Can be configured to both Host and Device.

Haptic feedback driver output

A DRV2605L haptic driver on the board (on I2C1) can be used to drive ERM and LRA haptic motors. Enhances feedback and conveys useful information to the users.

 

Display unboxing

Have a look what you will get when you will order a sample of similar product – STM32 Embedded Display 10.1″.

External memories

64Mb External SDRAM with 32-bit data bus

The synchronous SDRAMs achieve high-speed data transfer using pipeline architecture.

32-bit wide access:

  • Enables faster access to data
  • Higher refresh rate – higher resolution and animations.

 

512Mb External QSPI

The board is equipped with a separate 512Mb flash memory. It can store pictures, music, video, fonts, etc. QSPI can be accessed over the SWD interface on the board with any official ST programmer.

Micro-SD card slot

Additional external storage. Supports uSD card type: SD, SDHC and SDXC cards.

TouchGFX support

Example demo board support package- “Smart home” is available in TouchGFX designer.

STM32 MOOCS

TouchGFX Webinar

TouchGFX Workshop

Wide input supply range

Power supply voltage ranges from 6.0 V- 48.0V. A wide power supply comes with a wide range of application. Reverse polarity protection which ensures the device is not damaged if the power supply polarity is reversed. The module also can be powered from interface connectors: RS232, RS485, 2xCAN FDs. They are internally connected.

 

Plug & Play PoE Addon (separate accessory)

PoE stands for Power over Ethernet and refers to the ability to use an Ethernet cord to carry network data and electrical power to connected devices. The 2 x 20-pin, 1.27 mm, pin sockets, are used to connect the Riverdi PoE Add-on Board. The Riverdi PoE Add-on Board features a 10/100M Ethernet Port with Power-Over-Ethernet enabled. It allows you to power the module through the Ethernet port.

Low EMI design

STM32 Embedded boards were designed with special attention paid to electromagnetic compatibility, a design that has given them a high immunity to external electromagnetic signals which otherwise could have disturbing influence on their working correctly.

Board is equipped with low noise backlight converters thanks to which they produce low electromagnetic interference (EMI) to the surrounding space. In consequence, external electronic devices or circuits do not need special electromagnetic screening.

The EMC measurements held in a specialized laboratory confirmed low electromagnetic emissions of STM32 Embedded modules, even when displaying dynamic pictures.

High brightness, IPS TFT

Typical surface luminance for a high brightness, IPS TFT displays is 800 up to 1000 cd/m² which means it is very bright even outdoors. The full viewing angles allow the user to interact with the display in a natural and intuitive way from every side. Please see the datasheet for more features.

Optical / Air Bonding

Enhancing the optical performance of your display

Optical bonding is a process of affixing the touch panel (or just the protective glass) to the display using a liquid adhesive, gel or dry (film). In general, this process improves the parameters of the module – the optical performance, as well as durability.

The air-gap is the reason for the phenomena of reflection of sunlight. So, when the display is off, the Visual Area (V.A) is never black – it is gray.

When removing the air gaps, we reduce the number of internal reflecting surfaces, which increase of optical performance. This phenomenon improves readability, by reducing the reflection and correct contrast.

Industrial Touch Screen

Reacts to the slightest touch

The PCAP (Projected Capacity touch panel) is classified as ‘industrial’ (as opposed to ‘consumer’) when it is able to operate correctly in more demanding, harsh conditions (i.e. disturbing electromagnetic fields around causing interferences with panel controller, water droplets present in the surrounding area also on panel glass), and react properly when touched by hands in gloves. It can be tuned at the factory, detect touch through thicker glass layers than consumer panels (6mm thick glass layer was tested with success in the Riverdi lab) and it uses an industrial grade chip controller. Such controllers have industrial manufacturer’s guidelines implemented and are guaranteed to be manufactured typically from 10 to 15 years without any changes.

Main features:

  • ILITEK Touch IC-ILI2132A, with 10 years guaranteed availability
  • USB/I²C interface/Optional UART
  • Supports cover glass thickness up to 15mm
  • Supports double gloves operation – not only nitrile –even double thicker gloves
  • Working with water on the surface
  • Multi-touch, up to 5 fingers
  • Great EMC, RS (radiated susceptibility) and CS (conductive susceptibility) performance
  • Touch performance could be easily tuned to fit specific needs

 

For more information please see this page.

Sleek design without any holes in the housing

A uxTouch display is a specially designed LCD TFT display which has a Projected Capacitive Touch (PTC). Thanks to their absolute flat design and multi-touch feature, they are the perfect choice for your project if you intend to have an interactive design and technology.

They feature a modern and sleek design without any holes in the housing.

On the technical side, they are a great option for industrial spaces since there is no dirt accumulation possible. They also feature chemically strengthened glass, which has increased durability, thanks to the process of ion-exchange. They are easy to assemble, easy to clean and easy to implement into your design.

Customized displays

You can customize displays in many different ways.

  • Change the color, shape, and size of the cover glass
  • Have your logo printed on the cover glass (or any other graphics you might need)
  • Add a different interface
  • Enhance the brightness of the screen
  • Change the thickness of the cover lens for the CTP
  • Choose a different viewing angle of the display
  • Change the pinout
  • Request different gasket assembly

 

As you can see the possibilities are endless. All you need to do is choose.

We will help you to get the perfect tailor-made product.

Additional information

Weight512 g
Dimensions257.96 × 168.6 × 14.09 mm
Size (inch.)

10.1"

Touch Screen

Projected Capacitive Touch Panel

Touch Screen Bonding Technology

Optical Bonding

Touch Screen Shape

uxTouch

Mounting Frame

Without Frame

LCD type

IPS, Normally black, TFT, Transmissive

Viewing direction

Full Angle

Active area (mm)

216.96×135.60

Dot pitch (mm²)

0.1695×0.1695

Pixel Arrangement

RGB Vertical Stripe

Resolution

1280×800

Brightness (cd/m²)

850

Graphics controller

STM32H757XIH6

Input Voltage (V)

6.0 – 48.0

Driver IC

CTP driver: ILI2132A

Surface Treatment

Anti-glare / Clear (for CTP)

Operating temp. (°C)

-20~70

Do you need something else?

Contact us now

STM32 Embedded Display – Capacitive Touch Panel – Optical bonding – 10.1-inch TFT LCD screen – RVT101HVSNWC00-B


Product variants

Touch Screen Bonding Technology

850 cd/m2

The process of affixing the touch panel to the display using a liquid adhesive. It improves the parameters of the module - the optical performance, as well as durability.

Optical Bonding

850 cd/m2

The process of affixing the touch panel to the display using a liquid adhesive. It improves the parameters of the module - the optical performance, as well as durability.

800 cd/m2

The air-gap is the reason for the phenomena of reflection of sunlight. So, when the display is off, the Visual Area (V.A) is never black - it is gray.

Air Bonding

800 cd/m2

The air-gap is the reason for the phenomena of reflection of sunlight. So, when the display is off, the Visual Area (V.A) is never black - it is gray.

Touch Screen Shape

uxTouch

Most newly built devices use the uxTouch panel. It is slightly larger than the display and is stuck to the outside of the device. This gives a sleek and modern feel.

uxTouch

uxTouch

Most newly built devices use the uxTouch panel. It is slightly larger than the display and is stuck to the outside of the device. This gives a sleek and modern feel.

aTouch

It has all the same advantages of modern technology as uxTouch but without the decorative aspect. The display is mounted from the inside of the device and into the classic hole.

aTouch

aTouch

It has all the same advantages of modern technology as uxTouch but without the decorative aspect. The display is mounted from the inside of the device and into the classic hole.


$293.57 unit price

$293.57


Part Number: SM-RVT101HVSNWC00-B

Tag: STM32H7